Screw & Nail Quantity Estimator
Quick answer: Count fasteners as pieces times joist crossings per piece times fasteners per crossing, then add a waste allowance. A 120-inch deck board on joists 16 inches apart crosses 8 joists, so 22 boards at 2 screws per crossing need 352 screws, or 388 with 10% waste. Enter your project below for the exact count and a buy quantity rounded up to the nearest 50.
This estimator counts the screws or nails a project needs from the pieces, their length, the fastener spacing, and a waste allowance. It covers deck boards, fence boards, and drywall sheets, and rounds the buy quantity up to the nearest 50.
Enter your numbers
Your results
How to use this calculator
Pick your project type, then enter the number of pieces, the length of each piece in inches, the fastener spacing, and the fasteners at each crossing. Set the waste percentage to cover dropped or stripped fasteners โ 10% is the default. Results update instantly.
For deck boards, spacing is the joist spacing and fasteners per crossing is 2. For drywall, set fasteners per crossing to 1 and spacing to the stud spacing.
How this is calculated
Crossings per piece = floor(piece length รท spacing) + 1. Base fasteners = pieces ร crossings per piece ร fasteners per crossing. Total with waste = ceiling(base ร (1 + waste %)). Buy quantity = total rounded up to the nearest 50.
The formula counts one crossing at the start of each piece plus one at every spacing interval, so a board shorter than the spacing still counts 1 crossing. Counts are estimates for planning: cuts, angles, and blocking can change the count on a real job.
Worked example
22 deck boards, each 120 inches long, at 16-inch spacing with 2 screws per joist and 10% waste: crossings = floor(120 รท 16) + 1 = 7 + 1 = 8; base = 22 ร 8 ร 2 = 352 screws; total = ceiling(352 ร 1.10) = 388 screws; buy quantity = 400 screws.
Reference data
| Project | Fasteners per crossing | Spacing |
|---|---|---|
| Deck boards | 2 screws per joist | 16 in on center |
| Fence boards | 2 screws per rail | Per rail (2โ3 rails per board) |
| Drywall sheets | 1 screw per stud crossing | 16 in on center in the field, 8 in at edges |
Cross-check: about 350 screws per 100 sq ft for 6-inch deck boards at 16-inch joist spacing.
Source: Hunker, 'How To Calculate The Number Of Screws Required For A Deck' (2026 build); drywall spacing per USG Gypsum Construction Handbook.
Method & sources
Results are estimates for planning. They are general information, not financial, medical, or professional advice.
Frequently asked questions
How many screws do I need for a deck?
Count joist crossings per board as floor(board length in inches divided by joist spacing in inches) plus 1, multiply by boards and by 2 screws per crossing, then add waste. A 22-board deck of 120-inch boards at 16-inch spacing needs 352 screws before waste and 388 with 10% waste.
How many screws per joist for deck boards?
Two screws per joist crossing is the accepted practice for deck boards, placed about 3/4 inch to 1 inch from each board edge. Wider boards of 8 inches or more can need three screws per crossing to limit cupping.
How many screws are in 100 square feet of decking?
About 350 screws per 100 square feet for 6-inch-wide boards on joists spaced 16 inches on center, per Hunker deck screw guide figures. Four-inch boards need about 480 screws for the same area because more boards cover the same surface.
What spacing do drywall screws need?
Drywall screws go 16 inches on center in the field and 8 inches on center at edges and around openings, per the USG Gypsum Construction Handbook. This calculator counts crossings from your spacing value, so set spacing to 16 inches and fasteners per crossing to 1 for a drywall sheet estimate.
How much waste should I add for screws and nails?
Add 10% for dropped, stripped, or misdriven fasteners, which matches the allowance in this calculator. Round the final count up to the nearest 50 so you buy a full box size and keep spares for repairs.