French Drain Gravel Calculator
Quick answer: A 50-foot trench 12 inches wide and 18 inches deep, with a 4-inch pipe and 10% waste, needs about 77.70 cubic feet of gravel, or 2.88 cubic yards. At an estimated 1.4 tons per cubic yard, that is about 4.03 tons. Enter your trench length, width, depth, pipe diameter, and waste percent to get the same figures for your drain.
This French drain gravel calculator subtracts the pipe volume from the trench volume, so you order gravel for the space around the pipe rather than the whole trench, then adds your waste allowance.
Enter your numbers
The total run of the French drain trench.
The width of the dug trench.
The depth of the dug trench.
The outside diameter of the perforated drain pipe.
Extra gravel for spillage, uneven ground, and compaction.
Your results
| Trench volume | โ |
|---|---|
| Pipe volume | โ |
| Gravel volume (before waste) | โ |
| Gravel volume (with waste) | โ |
| Estimated weight | โ |
| Estimated 0.5 cu ft bags | โ |
Weight and bag counts are estimates. Gravel density varies by stone type and moisture, so confirm the conversion with your supplier before ordering.
How to use this calculator
Measure the trench length in feet and the width, depth, and pipe diameter in inches. Add a waste allowance to cover spillage and uneven ground, then read the gravel volume with waste as your order quantity.
Order by cubic yards from a bulk supplier when the job is large, or by bags for small runs. The bag count assumes 0.5-cubic-foot bags and is rounded up to whole bags.
How this is calculated
Trench volume (cu ft) = length (ft) ร width (in รท 12) ร depth (in รท 12). Pipe volume (cu ft) = ฯ ร (pipe diameter in รท 24)ยฒ ร length (ft). Gravel volume before waste = trench volume โ pipe volume. Gravel volume with waste = gravel volume ร (1 + waste percent รท 100). Cubic yards = cubic feet รท 27.
Weight is an estimate: tons = cubic yards ร 1.4, using 1.4 tons per cubic yard as the stated gravel-density estimate. Bag count = cubic feet with waste รท 0.5, rounded up. The pipe is treated as a solid cylinder, which is a conservative simplification because a perforated pipe displaces slightly less volume than a solid one.
Worked example
Inputs: 50 ft long, 12 in wide, 18 in deep, 4 in pipe, 10% waste. Trench volume = 50 ร 1 ร 1.5 = 75.00 cu ft. Pipe volume = ฯ ร (4 รท 24)ยฒ ร 50 = 4.36 cu ft. Gravel before waste = 75.00 โ 4.36 = 70.64 cu ft (2.62 cu yd). With 10% waste: 77.70 cu ft (2.88 cu yd). Estimated weight = 2.88 ร 1.4 = 4.03 tons. Estimated bags = 77.70 รท 0.5 = 156 bags (rounded up).
Reference data
| Item | Value |
|---|---|
| Cubic feet per cubic yard | 27 (defined conversion) |
| Gravel weight estimate | 1.4 tons per cubic yard (estimate โ varies by stone type) |
| Bag size used for the bag count | 0.5 cu ft per bag |
| Pipe diameters in this calculator | Any diameter in inches; 4 in is a common French drain pipe size |
Source: Defined unit conversions (27 cu ft = 1 cu yd) and the stated gravel-density estimate of 1.4 tons per cubic yard; page built 2026.
Method & sources
The calculator uses the trench-minus-pipe geometry stated above and the stated density estimate. Confirm the density with your supplier, since stone type and moisture change the weight.
Frequently asked questions
Why subtract the pipe volume?
The pipe occupies space inside the trench, so gravel goes only into the space around it. Subtracting the pipe volume avoids ordering gravel for space the pipe already takes up.
How many tons of gravel do I need?
Multiply cubic yards by the density estimate of 1.4 tons per cubic yard. The result is an estimate: confirm the density with your supplier before ordering.
What waste percent should I use?
10% covers spillage, uneven trench walls, and settling on most straight runs. Use a higher percent for rocky ground or trenches with many bends.
Does this include gravel under the pipe?
Yes. The trench volume covers the full depth, and only the pipe cylinder is subtracted, so gravel below, beside, and above the pipe is included.